Top 10 typical forklift mishaps ， forklift procedure must focus on these issues ！.

Don't take too lightly the forklift at the office. If the procedure is bad, there will certainly be severe crashes in mins, and there are several crashes entailing forklifts.

Case 1: The forklift cargo blocked the chauffeur's sight, and the person in front could not be found, resulting in a moving crash.
Instance 2: In order to keep the equilibrium of the forklift when raising heavy products, the employees used their body weight as the counterweight, which nearly triggered casualties.
Situation 3: The width of the forklift cargo exceeds the allowable size of the path and hangs on the roadside shelf, which almost creates an crash.
Situation 4: Forklift is speeding and rolls over throughout a turn.
Instance 5: The forklift motorist did not observe the pedestrian, and the pedestrian did not discover the forklift.
Case 6: The forklift lifts the employees illegally, the forklift vehicle driver does not put on the safety belt, the forklift lifter falls and the chauffeur is crushed when the forklift rolls over.
Case 7: The forklift chauffeur did not wear a safety belt and fell from the vehicle when it surrendered and was crushed.
Forklift operation need to take notice of these matters ：.

Start.
1. Prior to starting, observe the environments, and after verifying that there are no obstacles that prevent the security of driving, honk the horn initially and then begin.
2. For cars with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) gauge must be risk-free before beginning.
3. When the forklift begins with a lots, the motorist should initially confirm that the tons is secure and trustworthy.
4. The begin has to be sluggish and constant.

Driving.
1. When driving, the height in between the bottom end of the fork and the ground should be kept at 300mm-400mm, and the pole should be slanted in reverse. .
2. Do not lift the fork too expensive when driving. When entering and leaving the task website or while driving, be careful that there will be no challenges overhead. When the load is traveling, the fork has to not be raised too expensive, which will certainly affect the stability of the forklift. .
3. After discharging, the fork needs to be lowered to the typical driving placement before driving. .
4. When turning, if there are pedestrians or automobiles close by, the driving signal should be provided first. High-speed doglegs are banned. High-speed sharp turns will trigger the automobile to shed side security and tip over. .
5. When the forklift is downhill, it is strictly prohibited to shut off the fire and slide, and it is restricted to brake instantly while driving with loads unless there are special situations.
6. When the forklift is running, it should follow the website traffic rules in the manufacturing facility and have to maintain a particular safety distance from the vehicle in front. .
7. When the forklift is running, the load must be in the lowest position that does not hinder the driving, and the gantry should be properly tilted back. The load will not be elevated other than when piling or packing. .
8. The height of the tons should not block the driver's sight. In unique situations, when the product affects the forward vision, drive at a low rate when turning around.
9. It is prohibited to switch on the ramp, nor to drive across the ramp. .
10. The safe driving rate of the forklift in the manufacturing facility area is 5 km/h, and it must drive safely at a reduced speed when entering the production workshop area. Electric Forklift Truck for Warehouse .
11. When the forklift is raised, raised or driven, it is prohibited for personnel to depend on the fork to hold things and play a balancing role. .
12. If troubles are discovered, they will be fixed and reported in a prompt manner, and they will never ever operate with illnesses or hide them.

packing and unloading.
1. When fork-loading things, the distance between both forks ought to be readjusted as required to make the load of both forks balanced and not manipulated, and one side of the product should protest the rack. .
2. It is restricted to deal with a single fork or utilize a fork top or pull. In special scenarios, security indication should be established to remind bordering pedestrians. .
3. In the process of packing and dumping products, the forklift must be stopped with the brake. .
4. The rate of the car should be sluggish and steady. Beware not to roll the wheels on the dunnage, so as not to extend the rolled items and injure people. .
5. When utilizing a fork to fork the goods, the fork should be as deep as possible under the lots, and it ought to be kept in mind that the fork tip must not touch various other goods or items. The lots should be supported with marginal back tilt of the gantry so that the tons does not glide backwards. The mast can be slanted forward slightly when the tons is decreased to allow for simple positioning of the lots and extraction of the forks. .
6. It is prohibited to fork products at broadband and collide with hard items with the fork head. .
7. When the forklift is functioning, it is restricted for people to stand around the fork, so as to prevent the collapse of the goods and injure individuals. .
8. Overloading is restricted, and it is restricted to utilize forks to raise employees to engage in high-altitude operations to avoid high-altitude falling mishaps. .
9. It is not enabled to make use of the brake inertia to slide, place, round or roll things. .
10. It is not permitted to use forks to pick, turn pallet unload.

Leaving .
1. It is forbidden to leave the forklift when the products on the fork are in the air. Before leaving the forklift, you should discharge the goods or lower the fork framework.
2. Pull the emergency brake manage to dead or dispirit the hand brake button.
3. The engine is switched off and the power is removed. (Except for unique scenarios, such as the motorist does not leave the automobile's line of vision and does not surpass 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the look ought to be inspected, and fuel, lubricating oil and air conditioning water need to be included.
2. Inspect the safety performance of beginning, running and stopping.
3. Inspect whether the lights and horn signals are complete and effective.
4. Throughout the procedure of the forklift, inspect whether the pressure and temperature level are typical.
5. After the forklift is running, the outside leakage needs to additionally be inspected and the seals should be changed in time.

Forklift Safety Operation Specifications.
1. You need to inspect prior to leaving the automobile;.
2. When you experience someone before you during driving, you should send out a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the low point of the freight must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming ought to not be too sharp to avoid the tendency of " complimentary turning";.
6. Adding and down the slope needs to be sluggish and uniform, and no switching on the slope is permitted.
7. Do not drive across the slope. When the gradient is more than 10%, the car needs to be driven backwards when worsening;.
8. When the forklift workers lug the goods and progress, if they run into big or hefty goods and most likely to the driver's view, they need to take the reversing workout
.
The "Eight Prohibitions" should be adhered to in the operation.
1. Single fork procedure is not allowed.
2. It is not enabled to raise the goods for long distance driving.
3. It is not Stand-on Electric Pallet Stacker enabled to grab the goods by turning over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and other dangerous chemicals with forks.
5. It is not permitted to use inertia force to get the goods.
6. It is not permitted to use braking pressure to expatriation round or easy-to-roll objects.
7. It is not enabled to bring individuals to work with the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is increased.
8. Do not drive side to side on inclines
.
Vehicle parking is not allowed under the list below problems.
1. Curves, narrow roads, railway crossings;.
2. Areas with a longitudinal incline more than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the section with the exact same size as the barrier need to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844